![\"IMGP6427\"](\"https:\/\/rv10.mirimar.org\/wp-content\/uploads\/2016\/04\/IMGP6427.jpg\")
<\/a>The transponder and ADSB antenna backing plates were covered with a thin coat of ProSeal, then clecoed into place to cure over night.\u00a0 Next day Rich drove the rivets while I bucked.\u00a0 This photo just shows me positioning the plates.<\/p>\n<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n <\/p>\n Simultaneous to what Eric and I were doing, Rich was custom measuring 3\/8″ closed cell foam for sound damping under the baggage and rear seat floors.\u00a0 A $13 Black\/Decker electric carving knife provided excellent results and was easy to use single-handed.<\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n After completion of business travel and a few weeks with some health issues, I finally got back in the swing of some consistent shop time.\u00a0 In addition, Rich arrived for a two week stint of helping drive the process forward. First up – alodine and prime a series of parts\u00a0 previously\u00a0 prepared (antenna brackets, reinforcement …<\/span> Continue Reading →<\/span><\/a><\/span><\/p>\n","protected":false},"author":2,"featured_media":0,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[10,40],"tags":[],"class_list":["post-1615","post","type-post","status-publish","format-standard","hentry","category-rv-10-build-project","category-section-33-baggage-area"],"_links":{"self":[{"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/posts\/1615","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=1615"}],"version-history":[{"count":8,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/posts\/1615\/revisions"}],"predecessor-version":[{"id":1638,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/posts\/1615\/revisions\/1638"}],"wp:attachment":[{"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=1615"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=1615"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=1615"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}<\/a><\/a>In preparing for attaching the NACA plates, we found a few of the #4 screw holes were not reachable for dimpling with a regular yoke on the main squeezer. The improvisation here was use the C-frame, then hit the male dimple die with a hammer. While the fixture was a bit heavy for Eric to hold, the results were very good.<\/p>\n<\/a><\/a><\/p>\n<\/a><\/a>In between work on the plane, a few adjustments for tools were performed.\u00a0 At left – Rich prepares the CherryMAX H704B riveter obtained from Raybourn’s estate sale. At right, I remove the J33 Arbor from a very nice Albrecht C130 chuck getting ready for installation in my refurbished Delta 17-900 drill press.<\/p>\n<\/a>Oops! We tried using the CherryMAX riveter on some cheap pop rivets on the forward floor boards.\u00a0 Big mistake.\u00a0 I had tested round head pop rivets on some scrap stock with acceptable results, but failed to do the same test off-plane with countersunk rivets. The result – the CherryMAX is so powerful, it sheered off the countersink portion of the rivet and ingested the stem deep into the pull mechanism causing a jam.\u00a0 Okay, take everything apart, but not so easy after using blue Loctite on the threads.\u00a0 The double nut approach on the collet finally worked, so back in business again.<\/p>\n<\/a><\/a>In the meantime, Rich continued on the floor panel prep and pulled most of the floor rivets by hand.\u00a0 The offset head of the CherryMAX will be used with special rivets in hard to reach locations.<\/p>\n<\/a><\/a>Here I am fitting the corrugated baggage wall (left) for match drilling into the baggage bulkhead (right) already installed with the tailcone attachment.<\/p>\n<\/a><\/a>After drilling the appropriate holes are dimpled, and nutplates for #8 screws are riveted in place with 3\/32 rivets.<\/p>\n<\/a>Here Rich gets started on fitting the baggage door components together.\u00a0 Next steps will be to make hinges and fit into the mid-skins for alignment and match drilling.<\/p>\n<\/a>A successful two week visit from Rich with much “progress” achieved.\u00a0 The term “work” should not be applied to this project anymore.<\/p>\n","protected":false},"excerpt":{"rendered":"