![\"imgp7098\"](\"https:\/\/rv10.mirimar.org\/wp-content\/uploads\/2016\/11\/IMGP7098.jpg\")
<\/a>The door bottom needs extensive trimming to get to the proper thickness.<\/p>\n<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n
<\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n <\/p>\n I had another forced pause from the shop due to business travel overseas.\u00a0 This weekend was getting back in action with Eric’s help on further cutting, fitting and sanding the fiberglass cabin cover. The door bottom needs extensive trimming to get to the proper thickness. Left and right sides need to …<\/span> Continue Reading →<\/span><\/a><\/span><\/p>\n","protected":false},"author":2,"featured_media":0,"comment_status":"open","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[10,44],"tags":[],"class_list":["post-1842","post","type-post","status-publish","format-standard","hentry","category-rv-10-build-project","category-section-43-cabin-cover"],"_links":{"self":[{"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/posts\/1842","targetHints":{"allow":["GET"]}}],"collection":[{"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=%2Fwp%2Fv2%2Fcomments&post=1842"}],"version-history":[{"count":4,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/posts\/1842\/revisions"}],"predecessor-version":[{"id":1846,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=\/wp\/v2\/posts\/1842\/revisions\/1846"}],"wp:attachment":[{"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=%2Fwp%2Fv2%2Fmedia&parent=1842"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=%2Fwp%2Fv2%2Fcategories&post=1842"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/rv10.mirimar.org\/index.php?rest_route=%2Fwp%2Fv2%2Ftags&post=1842"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}<\/a>Left and right sides need to be notched to accommodate the bulkhead reinforcements at the bottom.\u00a0 Notice the degree of relief needed to make this fit.<\/p>\n<\/a>The inner section must line up just right with the mid-skin longerons.\u00a0 Too much taken off will decrease strength for the connecting rivets.\u00a0 Too little and the fiberglass bottoms out on the longeron and fit will not be proper.<\/p>\n<\/a>First reduction was with a fiberglass cutting wheel on a Dremel tool, followed by a belt sander, hand file and finally Great Lakes 22″ sanding block with 120 grit paper.<\/p>\n<\/a><\/a>Fit, trim and refit is the process here. Getting the cabin cover to slide in without too much material removed takes time and patience.\u00a0 On the right photo the 3\/4″ offset for windshield and doors are being highlighted with a Sharpie.<\/p>\n<\/a><\/a>Trim the windshield flange…<\/p>\n<\/a>Clamp the rear door pillar and bottom flange in place.\u00a0 Then start the match drilling of the cabin cover to the top tailcone skin.<\/p>\n<\/a><\/p>\n<\/a>Eric pushes up on the cabin cover fiberglass while I drill #30 holes down through the tailcone skin. This process will continue on around the whole baggage bulkhead area.<\/p>\n","protected":false},"excerpt":{"rendered":"